HPT Series High-Efficiency Hydraulic Cone Crusher combines crushing stroke with crushing chamber perfectly, which makes capacity improved and efficiency increased. Besides, hydraulic lubrication control system helps bearing of hydraulic cone crusher get double protection.
1.
advanced crushing principle and technical data, reliable operation and low operation cost. All parts of the crusher have anti-wearing protection, which can make the life time of spare parts increased by 30% and the maintenance cost decreased to the lowest. The crusher avoids the disadvantages of impact crusher like low average crushing ratio, large energy consumption, fast abrasion of blow bar, impact plate and lining board.
2.
The crusher adopts between-layer pressuring crushing principle and suitable turning speed, not the traditional single particle crushing principle. The special crushing cavity can make the crusher crush materials selectively, thus the proportion of fine product and product of cubic shape is increased distinctly and product of lump size is decreased by a large extent.
3.
Unique design of thin oil lubrication system prolongs life time of the crusher, high performance and not touchable labyrinth airproof part block off dust and remove common disorders like mixture of oil and water in spring cone crusher.
4.
Discharge opening is adjusted by hydraulic device and overload protection makes performance of the crusher increased by a large extent, maintenance and operation are easier, repairing time is shorter.; the bidirectional metal releasing hydraulic vat makes slab pass through crushing cavity；the crusher can discharges material automatically when the hydraulic device works under the condition of iron passing and instantaneous overloading, thus there is no trouble of stopping the crusher to discharge material by hand.
5.
It only need change fixed cone lining board and movable cone lining board; , the type of crushing cavity can be changed from standard coarse cavity to short head fine cavity, which can meet various kinds of requirements.
6.
all parts of HPT series of cone crusher can be assembled, disassembled and repaired from the top and side part, including the fixed cone and movable cone. If change, no need to disassemble the crusher body and fasten the bolts. Hydraulic motor makes the performance of crusher better.
Working Principle
Under the leading role of eccentric sleeve, the movable cone of the HPT Series high-efficiency hydraulic cone crusher does rotary and pendulum movement which drives the broken walls squeeze and twist the raw material between the rolling ace tabular wall and it. According to laminated theory, the raw material is crushed and polished following their own texture by the force from different directions. Stable aggregate are produced finally. The eligible raw material falls down from the gap of the broken wall. The others will be kept crushing until it reaches the desired size.
NK wheel‑type mobile crushing plant is semi‑mobile equipment integrating feeding, crushing, screening and conveying on wheel chassis. It requires no large concrete foundation and is towed by trailer for relocation. It suits scattered quarries, short
Vertical preheater is installed at kiln tail to recover waste heat from hot kiln flue gas. It heats normal‑temperature limestone close to decomposition point. Partial carbonate decomposes in advance to reduce calcination load, cut fuel consumption and improve lime activity. Circular and polygonal types are available for different capacity grades. Preheater specification must match kiln capacity, flue‑gas temperature and flow to keep stable thermal condition for energy‑saving lime lines.
Heat rate (kJ/kg‑CaO) means heat consumption for producing each kilogram of CaO. Our kiln series reaches 4810‑5300 kJ/kg‑CaO. High raw‑material impurity, poor preheater performance, serious air‑leakage and insufficient cooler heat‑recovery will increase heat consumption. Large‑capacity models with polygonal preheater deliver lower heat rate. Good sealing and regular maintenance for preheater & cooler help control heat‑rate and cut fuel operating cost.
Small single‑drum dryer allows max inflow temperature ≤700℃; medium‑large single‑drum (≥φ1500) ≤800℃; three‑tube dryer runs at 700‑750℃. Do not keep full‑limit temperature in real operation; avoid material over‑burning according to material heat resistance. Excessive temperature accelerates high‑temperature oxidation of drum and lifters and shortens wearing‑part service life. Operators shall strictly control heating parameters.
For identical ultra‑fine powder fineness, MW ring‑roller mill has much lower procurement cost and unit‑product energy consumption than jet mill, with larger single‑machine throughput and lower OPEX. Yet its ultimate finest limit is inferior to je
The LM Vertical Slag Grinding Mill has its own hot-air system using kiln waste heat or a hot-air furnace to remove moisture during grinding. Feed moisture up to about 15% is quickly dried by high-temperature airflow, completing drying, grinding and class
RELATED CASE
Request a quotation
Copyright © LIMING MACHINERY CO., LTD. All rights reserved Privacy Policy
